series am 40uw -iz 40 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 1 of 5 north america only picture coming soon features: ? ultra - wide input 4 :1 range ? adjustable output voltage ? 1 5 00 & 3000 vdc isolation ? remote on/off function ? efficiency up to 87% ? over load, voltage & short circuit protection ? regulated output ? operating temperature - 40 o c to + 7 5 o c ? soft start models single output model input voltage (v) output voltage (v) output current max ( a) isolation (vdc) efficiency (%) am40u w - 2403siz 9 - 36 3.3 7 1500 8 2 am40uw - 2405siz 9 - 36 5 7 1500 82 am40uw - 2412siz 9 - 36 12 3 1500 82 am40uw - 2415si z 9 - 36 15 2.3 1500 82 am40uw - 2424siz 9 - 36 24 1.5 1500 82 am40uw - 48 03siz 18 - 75 3.3 7 1500 83 am40uw - 4805siz 18 - 75 5 7 1500 83 am40uw - 4812siz 18 - 75 12 3 1500 83 am40uw - 4815siz 18 - 75 15 2.3 1500 83 am40uw - 4824siz 18 - 75 24 1.5 1500 83 am40uw - 2403s h30iz 9 - 36 3.3 7 3000 82 am40uw - 2405sh30iz 9 - 36 5 7 3000 82 am40uw - 2412sh30iz 9 - 36 12 3 3000 82 am40uw - 2415sh30iz 9 - 36 15 2.3 3000 82 am40uw - 2424sh30iz 9 - 36 24 1.5 3000 82 am40uw - 4803sh30iz 18 - 75 3.3 7 3000 83 am40uw - 4805sh30iz 18 - 75 5 7 3000 83 am4 0uw - 4812sh30iz 18 - 75 12 3 3000 83 am40uw - 4815sh30iz 18 - 75 15 2.3 3000 83 am40uw - 4824sh30iz 18 - 75 24 1.5 3000 83 models dual output model input voltage (v) output voltage (v) output current max (a) isolation (vdc) efficiency (%) am40uw - 2405diz 9 - 36 5 3.5 1500 80 am40uw - 2412diz 9 - 36 12 1.5 1500 80 am40uw - 2415diz 9 - 36 15 1.15 1500 80 am40uw - 4805diz 18 - 75 5 3.5 1500 81 am40uw - 4812diz 18 - 75 12 1.5 1500 81 am40uw - 4815diz 18 - 75 15 1.15 1500 81 am40uw - 2405dh30iz 9 - 36 5 3.5 3000 80 am40uw - 2412dh30iz 9 - 36 12 1.5 3000 80 am40uw - 2415dh30iz 9 - 36 15 1.15 3000 80 am40uw - 4805dh30iz 18 - 75 5 3.5 3000 81 am40uw - 4812dh30iz 18 - 75 12 1.5 3000 81 am40uw - 4815dh30iz 18 - 75 15 1.15 3000 81 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.
series am 40uw -iz 40 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 2 of 5 north america only input specifications parameters nominal typical maximum units voltage range vdc 24 9 - 36 48 18 - 75 filter (pi) network absolute maximum rating vdc 24 50 48 100 on/off c ontrol on C ttl high or open ; off C ttl low or short isolation specifications parameters conditions typical maximum units tested i/o voltage 3 sec 1500 or 3 0 00 vdc resista nce 500vdc >1000 mohm output specifications parameters conditions typical maximum units voltage accuracy 2 % over voltage protection zener diode clamp over current protection >110 fl % short circuit protection continuous short circuit restart auto - restart line voltage regulation 0.5 % of vin load voltage regulation (single) iout=25% to 100% 0.5 % load voltage regulation (dual) iout=25% to 100% 2 % temperature coefficient 0.05 %/ o c ripple & noise 20mhz bandwidth (5 & 3.3vout) 80 mv p - p all other output models 1 % p - p vout voltage adjustment range 10 % minimum load current 25 % of max general specifications parameters conditions typical maximum units switching frequency 100 % load 250 khz operating temperature - 40 to +85 o c storage temperature - 55 to +11 5 o c maximum case temperature 100 o c derating see chart below 45 o c cooling free air convection humidity 95 % rh case material nickel C coated copper with nonconductive base weight 65 g dimensions (l x w x h) 2.00 x 2.00 x 0.40 inches 50.81 x 50.81 10. 20 mm mtbf > 1 5 00 000 hrs ( mil - hdbk - 217 f at +25 o c ) maximum s oldering t emperature o c transient r ecovery time 50% load step change 280 u s
series am 40uw -iz 40 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 3 of 5 north america only pin out specifications pin 1000 & 3000 vdc single dual 1 +v input +v input 2 - v input - v input 3 on/off control on/off control 4 no pin +v output 5 +v output common 6 - v output - v output 7 trim trim dimensions 50.80 (2.00) 50.80 (2.00) 1 2 3 10.16 (0.40) 5.08 (0.20) 45.70 (1.80) 4 5 6 7 22.86 (0.90) 10.16 (0.40) 10.16 (0.40) 10.16 (0.40) side view 1.00 (0.04) 5.60 (0.22) dimensions mm (inch) case tolerance: 0.25mm (0.02inch) pin length tolerence: 0.05mm (0.002inch) bottom view printed face trimming
series am 40uw -iz 40 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 4 of 5 north america only derating - 40 - 20 0 20 40 60 80 100 100 80 60 40 20 0 safe operating area output power (%) 75 ambient temperature o c free air convection 35 45 o c contro l on/off pin connection example single output dual output
series am 40uw -iz 40 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 5 of 5 north america only digital control circuit: control voltage on / off control -v input 0.5ma dc/dc converter npn 0v vpeak ra = vpeak C 0.6 0.5ma note: 1. datasheets are updated as needed and as such, specific ations are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications o n labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4 . all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not hav e conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may n ot be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet . 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com .
|